Indesit FZ 61.1 IX Bedienungsanleitung PDF herunterladen (Seite 15)

DATA PLATE

Dimensions

width cm 43.5

height cm 32

depth cm 41.5

Vol ume lt. 58

Dimensions of

models with

removable racks

width cm 37.5

height cm 32

depth cm 41.5

Volume of models

with removable

racks

lt. 50

Electrical

connections

voltage: 220-230V~ or 220-240V~

50/60 Hz or 50Hz (see data plate)

maximum power absorbed 2800W

ENERGY LABEL

Directive 2002/40/EC on the label

of el ectric ovens.

Norm EN 50304

Energy consumption for Natural

convection – heating mode:

Traditional mode

Declared energy consumption for

Forced convection Class – heating

mode: Baking

This appli ance conforms to the

following European Economic

Community directives:

-2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2 004/ 108 /EEC of 15/ 12/04

(Electromagneti c Compatibil ity) a nd

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EC and subsequent

amendments.

Electrical connections

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating current

at the voltage and frequency indicated on the data

plate located on the appliance (

see below

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the side

tabs of the cover. Use

the screwdriver as a

lever by pushing it down

to open the cover (

see

diagram

2. Install the power

supply cable by

loosening the cable

clamp screw and the

three wire contact

screws L-N-

Connect the wires to the

corresponding terminals:

the Blue wire to the

terminal marked (N), the

Brown wire to the

terminal marked (L) and

the Yellow/Green wire to

the terminal marked

(

see diagram

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (

see side

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

mains, suitable for the load indicated and complying with

current electrical regulations (the earthing wire must not be

interrupted by the circuit-breaker). The supply cable must

not come into contact with surfaces with temperatures

higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant with

safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate (

see

below

• The voltage must be in the range between the

values indicated on the data plate (

see below

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (

see Assistance

! The manufacturer declines any liability should! The manufacturer declines any liability should

! The manufacturer declines any liability should

these safety measures not be observed.these safety measures not be observed.

these safety measures not be observed.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FZ 61.1 IX Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit FZ 61.1 IX