Indesit FK 104 S P 0 X/HA S Bedienungsanleitung PDF herunterladen (Seite 37)

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the

lamp-holder.

2. Remove the light bulb and replace it

with a similar one: halogen lamp voltage

230 V, wattage 25 W, cap G 9.

3. Replace the glass cover (see

diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding racks:

1. Remove the two frames, lifting them

away from the spacers A (see gure).

2. Choose which shelf to use with the

sliding rack. Paying attention to the

direction in which the sliding rack is to

be extracted, position joint B and then

joint C on the frame.

3. Secure the two frames with the guide

rails using the holes provided on the

oven walls (see diagram). The holes

for the left frame are situated at the

top, while the holes for the right frame

are at the bottom.

4. Finally, t the frames on the spacers

! Do not place the sliding racks in position 5.

Automatic cleaning by PYROLYSIS

The cleaning cycle can cause the internal temperature of the oven to reach

500°C. The pyrolytic cycle is activated, burning away food and grime residues.

Dirt is literally incinerated.

Keep children away from the appliance during the automatic cleaning cycle

as surfaces may become very hot. Particles may ignite inside the oven as a

result of the combustion process. There is no cause for concern: this process

is both normal and hazard-free.

Before initiating the PYROLYTIC cycle:

• clean the oven door;

• remove large or coarse food residues from the inside of the oven using a

damp sponge. Do not use detergents;

• remove all accessories and the sliding rack kit (where present);

• do not place tea towels or pot holders over the oven handle.

Glass cover

Lamp

Holder

compartment

Left

guide rail

Right guide

rail

Direction

of extraction

! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to

cool down.

! The programme may only be started once the oven door has been closed.

To activate the cleaning cycle :

1. Press to switch on the control panel.

2. Press the icon.

3. Scroll through the menu commands using the control dial, select

PYROLYTIC and press .

4. The appliance suggests a “NORMAL” pyrolytic cycle, with a duration of 1

hour 30 minutes. Other levels of cleaning may be selected.

• Use the control dial to select one of the following:

- “ECONOMY”: duration 1 hour

- “NORMAL”: duration 1 hour and 30 minutes

- “INTENSIVE”: duration 2 hours.

• Press again.

5. Press to begin the PYROLYTIC cycle.

Safety devices

• the door locks automatically as soon as the temperature reaches a high

value; the icon lights up on the display.

• pressing the icon cancels the cleaning cycle at any time.

• if a malfunction occurs, the heating elements will be switched off.

• once the oven door has been locked, you cannot change the duration and

end time settings.

Programming delayed automatic cleaning

! Programming is possible only after selecting the cleaning cycle.

1. Press the icon twice; the end of pyrolysis time will begin to ash.

2. Turn the control dial to adjust the end of pyrolysis time; hold the dial in this

position to scroll through the numbers more quickly and make the setting

process easier. The display will show a graphic indicating the delayed start

in bar format.

3. Once you have reached the desired end time, press the icon again.

The delayed start bar will show the current time, the time remaining until the

start of pyrolysis, the duration and the end of pyrolysis time as a graphic.

4. Press to begin the pyrolysis schedule.

5. The display shows the remaining time, moving the delayed start bar

backwards.

6. Once pyrolysis has begun, the display will indicate the remaining time by

lling the duration bar.

7. When the time has elapsed, “CLEANING CYCLE FINISHED” appears on

the display and a buzzer sounds.

• For example: it is 9:00 a.m. and the Economy PYROLYTIC cycle has been

selected: default set time 1 hour. 12:30 is scheduled as the end time. The

programme will start automatically at 11:30 a.m.

To cancel a schedule, press the icon.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FK 104 S P 0 X/HA S Bedienungsanleitung Seite 37

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit FK 104 S P 0 X/HA S