Indesit IS50D1XXS Bedienungsanleitung PDF herunterladen (Seite 5)

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used

with a different type of gas, replace the old rating

label with a new one that corresponds to the new

type of gas (these labels are available from

Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

to “regulators for channelled gas”.

TECHNICAL DATA

Oven dimensions

(HxWxD)

34x39x44 cm

Volume

60 l

Useful

measurements

relating to the

oven

compartment

width 42 cm

depth 44 cm

height 23 cm

Power supply

voltage and

fre

uenc

see data plate

Burners

may be adapted for use with any

type of gas shown on the data

plate, which is located inside the

flap or, after the oven compartment

has been opened, on the left-hand

wall inside the oven.

ENERGY LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN

50304

Declared energy consumption for

Natural convection Class – heating

mode:

Static

EC Directives: 2006/95/EEC dated

12/12/06 (Low Voltage) and

subsequent amendments -

89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments -

2009/142/EC dated 30.11.09 (Gas)

and subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments -

2002/96/EC.

1275/2008 (Stand-by/ Off mode)

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory

screw, which is positioned inside or next to the tap

pin, until the flame is small but steady.

! If the appliance is connected to a liquid gas

supply, the regulatory screw must be fastened as

tightly as possible.

3. While the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame is not

extinguished.

Disposing of the appliance

When disposing of the appliance please remove the

plug by cutting the mains cable as close as

possible to the plug body and dispose of it as

described above.

Checking the connection for leaks

When the installation process is complete, check

the hose fittings for leaks using a soapy solution.

Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and

slide the burners off their

seats.

2. Unscrew the nozzles using

a 7 mm socket spanner (

see

figure

), and replace them with

nozzles suited to the new type

of gas (

see Burner and nozzle

specifications table

3. Replace all the components by following the

above instructions in reverse.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUEBLUE

BLUE “

NEUTRALNEUTRAL

NEUTRAL” (“

N”)

BROWNBROWN

BROWN “

LIVELIVE

LIVE” (“

L”)

GREEN AND YELLOWGREEN AND YELLOW

GREEN AND YELLOW “

EARTHEARTH

EARTH” (“

E”)

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit IS50D1XXS Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küche Indesit IS50D1XXS