Indesit K3C55(X)/R Bedienungsanleitung PDF herunterladen (Seite 4)

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Installation

The following instructions should be carried out by a qualified

technician to ensure that the appliance is installed, adjusted

and technically serviced correctly in compliance with current

regulations.

Important: always disconnect the cooker from the power

supply cable before carrying out any maintenance operations

or adjustments, etc.

Positioning

The appliance may be installed next to cabinets that are not

taller than the worktop. The following precautions must be

taken when installing the cooker:

a) Kitchen cabinets adjacent to the appliance and taller than

the worktop must be at least 200 mm from the edge of

the top.

b) Hoods must be installed according to their relative

installation instruction manuals and at a minimum distance

of 650 mm from the worktop.

c) Position the wall cabinets adjacent to the hood at a

minimum height of 420 mm from the worktop (see figure).

d) If the hob is installed beneath a wall cabinet, the latter

must be situated at a minimum of 700 mm (millimetres)

above the worktop as shown in the figure.

e) The installation cavity should have the dimensions

indicated in the figure.

Levelling

Adjustable feet (see fig. 1) are supplied with the cooker in

order to ensure it is perfectly level. These may be screwed

into the holes provided on each corner of the base of the

cooker.

Electrical connection

The cable should be suited to the type of electrical connection

used (see connection diagram below).

Installing the power supply cable

To open the terminal board:

• Loosen the screw “V”.

• Remove the junction block cover by pulling it.

To install the power supply cable, follow the instructions below:

• position the small A-B connection according to the type

of connection you wish to carry out, following the diagram

in figure 3.

Note: the Factory prepares small connections for 230V single-

phase connection (contacts 1-2-3 are connected to each

other). The 4-5 jumper is located on the lower area of the

terminal board.

• Position the cables (N and

) as demonstrated in the

figure and tighten the corresponding screws.

• Fasten the remaining cables to terminals 1-2-3.

• Secure the power supply cable by fastening the cable

clamp screw then replace the cover using the screw “V”.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated

on the data plate. If the appliance is directly connected to the

mains supply, an omnipolar circuit-breaker (switch) should

be fitted, with a minimum contact opening of 3 mm. This

switch must be able to withstand the maximum load of the

appliance and must conform to all current safety regulations

(the earth wire should not be interrupted by the switch). The

power supply cable should be positioned in such a way that

it does not reach temperatures of more than 50°C over the

temperature of the room, along its whole length. Before

connecting the appliance to the power supply, make sure

that:

• The modulating valve and the electricity supply can

withstand the maximum power of the appliance (see data

plate for details).

• The power supply has an efficient earthing system that

conforms to current regulations.

• the socket or the switch is easily accessible once the

cooker has been installed.

1 2

12345

400V 3N

H05RR-F 5x2.5 CEI-UNEL 35363

400V 2N

H05RR-F 4x4 CEI-UNEL 35363

230V

H05RR-F 3x4 CEI-UNEL 35363

1 2 3 4 5 6 7 8 9 ... 61 62

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit K3C55(X)/R Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit K3C55(X)/R