Indesit C 34S G3 (X) R /HA S Bedienungsanleitung PDF herunterladen (Seite 18)

If it is necessary to level

the appliance, screw the adjustable feet into the places

provided on each corner of the base of the cooker (see

 g.

The legs* fit into the slots on the

underside of the base of the

cooker.

Electrical connection

Install a standardised plug

corresponding to the load

indicated on the appliance data

plate .

see Technical data table

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

mains. The circuit-breaker must be suitable for the charge

indicated and must comply with NFC 15-100 regulations

(the earthing wire must not be interrupted by the circuit-

breaker). The supply cable must be positioned so that it

does not come into contact with temperatures higher than

50°C at any point.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

* Only available in certain models

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a flexible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of gas

with which it will be supplied (see the rating sticker on

the cover: if this is not the case see below). When using

liquid gas from a cylinder, install a pressure regulator

which complies with current national regulations. To

make connection easier, the gas supply may be turned

sideways*: reverse the position of the hose holder with

that of the cap and replace the gasket that is supplied

with the appliance.

! Check that the pressure of the gas supply is

consistent with the values indicated in the Table

of burner and nozzle specifications (see below).

This will ensure the safe operation and durability of

your appliance while maintaining efficient energy

consumption.

Gas connection using a flexible rubber hose

Make sure that the hose complies with current national

legislation. The internal diameter of the hose must

measure: 8 mm for liquid gas supply; 13 mm for

methane gas supply.

Once the connection has been performed, make sure

that the hose:

• Does not come into contact with any parts that reach

temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and

that it is not kinked or bent.

• Does not come into contact with blades, sharp

corners or moving parts and that it is not

compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will

be fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled

or if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

Levelling

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only.

! The manufacturer declines any liability should

these safety measures not be observed.

hose must be used instead (see below).

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit C 34S G3 (X) R /HA S Bedienungsanleitung Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Indesit C 34S G3 (X) R /HA S