Indesit TV 631 E (BK) GH Bedienungsanleitung PDF herunterladen (Seite 15)

Connecting a flexible jointless stainless steel pipe to a

threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas

cylindrical male attachment.

These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once

connection has been carried out, make sure that the

flexible metal pipe does not touch any moving parts and

is not compressed.

 Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

 When the installation process is complete, check the

pipe fittings for leaks using a soapy solution. Never use a

flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base of

the hob or on the packaging), the burner nozzles should

be replaced as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for

the new type of gas (see table 1

Burner and nozzle

characteristics).

In the case of

the Mini WOK, use a spanner

with a 7 mm opening to

unscrew the nozzle (see

figure).

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

Replacing the Mini DUAL burner nozzles

1. Remove the hob grids and slide the burners off their

seats. The burner consists of two separate parts.

2. Loosen the 3 screws and remove the burner.

3. Loosen the 2 screws (see figure).

4. Unscrew nozzle "A" using a 7

mm socket spanner. Use a

spanner with a 7 mm opening to

unscrew nozzle "B" (see figure).

Replace the nozzles with models

which are suitable for use with the

new type of gas (see table 1).

5. Replace all the components

by following the above instructions in reverse.

 Adjusting the burners primary air :

Does not require adjusting.

 Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust

the adjustment screw, which is

positioned in or next to the tap

pin, until the flame is small but

steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are

set to the low flame setting, increase this low flame

setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax or a similar

substance.

 If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

 Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

 Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in order

to comply with current national regulations).

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit TV 631 E (BK) GH Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Indesit TV 631 E (BK) GH