Indesit KP9F11S(K)/G S Bedienungsanleitung PDF herunterladen (Seite 5)

The switch must be suitable for the charge indicated and

must comply with current electrical regulations (the earthing

wire must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point.

Before connecting the appliance to the power supply, make

sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked “E”

or or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or

coloured Red.

Connect the Blue wire to the terminal marked “N” or

coloured Black.

FAILURE TO OBSERVE THE ACCIDENT-PREVENTION

REGULATIONS RELIEVES THE MANUFACTURER OF

ALL LIABILITY.

Replacing the cable

Use a rubber cable of the type H05VV-F with a cross section

of 3 x 1.5 mm². The yellow-green earth wire must be 2 ÷ 3

cm longer than the other wires.

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a exible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of gas

with which it will be supplied (see the rating sticker on the

cover: if this is not the case see below). When using liquid

gas from a cylinder, install a pressure regulator which

complies with current national regulations.

! Make sure that the gas supply pressure is consistent

with the values indicated in the Table of burner and nozzle

specifications (see below). This will ensure the safe

operation and durability of your appliance while maintaining

efcient energy consumption.

Gas connection using a exible rubber hose

Make sure that the hose complies with current national

legislation. The internal diameter of the hose must measure:

8 mm for a liquid gas supply;13 mm for a methane gas

supply.

Once the connection has been performed, make sure that

the hose:

• Does not come into contact with any parts which reach

temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and that it

is not kinked or bent.

• Does not come into contact with blades, sharp corners

or moving parts and that it is not compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits rmly into place at both ends, where it will be xed

using clamps which comply with current regulations.

! If one or more of these conditions is not fullled or if the

cooker must be installed according to the conditions listed

for class 2 - subclass 1 appliances (installed between two

cupboards), the exible steel hose must be used instead

(see below).

Connecting a exible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation. To begin using the hose, remove the

hose holder on the appliance (the gas supply inlet on the

appliance is a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose length

does not exceed a maximum of 2 metres, making sure that

the hose is not compressed and does not come into contact

with moving parts.

Checking the connection for leaks

When the installation process is complete, check the hose

ttings for leaks using a soapy solution. Never use a ame.

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit KP9F11S(K)/G S Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küchen- und Haushaltswarenzubehör Indesit KP9F11S(K)/G S