Indesit FZ 99 P.1 GIX F Bedienungsanleitung PDF herunterladen (Seite 15)

Electrical connection

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2. Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Remove the wire

contact screws L-N-

, then fasten the wires

under the screw heads,

respecting the colour

code: Blue (N), Brown

(L) and Yellow-Green

Verde (

Connecting the electricity supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see table).

The appliance must be directly connected to the mains

using an omnipolar switch with a minimum contact

opening of 3 mm installed between the appliance and

the mains. The switch must be suitable for the charge

indicated and must comply with current electrical

regulations (the earthing wire must not be interrupted

by the switch). The supply cable must be positioned

so that it does not come into contact with temperatures

higher than 50°C at any point.

! The installer must ensure that the correct electrical

connection has been made and that it is fully

compliant with safety regulations.

Before connecting the appliance to the power

supply, make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate (see below).

 The voltage is in the range between the values

indicated on the data plate (see below).

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

! The manufacturer declines any liability should

these safety measures not be observed.

TABLE OF CHARACTERISTICS

Dimensions

width 43.5 cm

height 32 cm

depth 40 cm

Volume

56 l

Dimensions *

width 43.5 cm

height 32 cm

depth 41.5 cm

Volume *

58 l

Electrical

connections

voltage: 220 - 240 V~ 50/60Hz

maximum power absorbed 2800 W

(see data plate)

ENERGY

LABEL

Directive 2002/40/EC on the label of

electric ovens. Standard EN 50304

Energy consumption for Natural

convection – heating mode:

Traditional mode

Declared energy consumption for

Forced convection Class – heating

mode: Baking

This appliance conforms to the

following European Economic

Community directives: 2006/95/EEC

dated 12/12/06 (Low Voltage) and

subsequent amendments -

89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments.

2002/96/EC

* Wit h glass pa nel fitted to the ins ide of the door

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FZ 99 P.1 GIX F Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Xilinx Carros manuales de usuario

Indesit FZ 99 P.1 GIX F Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit FZ 99 P.1 GIX F

Xilinx Carros manuales de usuario