Indesit PFTA++ 8H4X Bedienungsanleitung PDF herunterladen (Seite 24)

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

Troubleshooting

Problem: Possible causes / Solutions:

The dishwasher does not start

or cannot be controlled.

• Switch off the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close.

• The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes

excessive noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to

the hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish

tinge.

• The rinse aid dosage is too high.

The crockery has not been

dried properly.

• A wash cycle without a drying program has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take

any water in - Tap shut-off

alarm

(several short beeps are emitted)

(the ON/OFF indicator light flashes and

A 6 appears on the display).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken

when the beeps sounded.

Switch off the appliance using the ON/OFF button, turn on the tap and

switch the appliance back on after 20 seconds by pressing the same

button. Re-program the appliance and restart the wash cycle.

Water inlet hose alarm / Water

inlet filter blocked

(the ON/OFF indicator light flashes and

A 7 appears on the display).

• Switch off the appliance by pressing the ON/OFF button. Shut off the

water tap to eliminate the risk of flooding and remove the plug from the

electrical socket.

Make sure the water inlet filter has not become blocked by impurities

(see “Care and maintenance” chapter).

* Only available in selected models.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 83 84

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit PFTA++ 8H4X Bedienungsanleitung Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit PFTA++ 8H4X