Indesit LFT7 H204 HX Bedienungsanleitung PDF herunterladen (Seite 15)

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

 The socket is earthed and complies with current

regulations.

 The socket can withstand the maximum load of the

appliance, which is indicated on the data plate

located on the inside of the door (see chapter entitled

Description of the appliance).

 The power supply voltage falls within the values

indicated on the data plate on the inside of the door.

 The socket is compatible with the plug of the

appliance. If this is not the case, ask an authorised

technician to replace the plug (see Assistance); do

not use extension cables or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket should be easily

accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick

the adhesive transparent strip under the wooden shelf in

order to protect it from any condensation which may

form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill the

salt dispenser with water and add only then

approximately 1 kg of salt (see chapter entitled Rinse aid

and refined salt). The water may overflow: this is normal

and is not a cause for concern. Select the water

hardness value (see chapter entitled Rinse aid and

refined salt). - After the salt has been poured into the

machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener

and the heating element may be damaged as a result.

* Only available in selected models.

Technical data

Dimensions

width 59.5 cm

height 82 cm

depth 57 cm

Capacity 14 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2005/32/EC (Comm. Reg.

1275/2008) (Ecodesign)

-97/17/EC (Labelling)

-2002/96/EC (WEEE)

Transportation

Unload all crockery from the dishwasher and secure

moving parts.

All water remaining inside the appliance should be

drained as follows:

make sure that the water tap is open and select the ECO

cycle. The cycle will begin. After 5 minutes, end the

cycle by pressing the ON/OFF button until you hear a

beep and the indicator lights switch off. Wait for

approximately 5 minutes before uninstalling the

appliance. Shut off the tap and disconnect the inlet and

drain hose.

The appliance should only be moved in an upright

position, in order to prevent any water remaining inside

the appliance from damaging dishwasher components.

Leaving the machine unused for extended

periods/Freezing protection

If the appliance is situated in a location which is at risk of

freezing, or if you intend to be away for extended periods

of time (e.g. holiday home), empty the appliance

completely.

- Carry out the process used to drain all water remaining

inside the appliance (see Transportation)

- Disconnect the appliance from the electricity supply

and shut off the water tap.

- Leave the appliance door ajar.

- When you return, run a cycle while the dishwasher is

empty.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 83 84

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit LFT7 H204 HX Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit LFT7 H204 HX