Indesit KP59MS-CX-G Bedienungsanleitung PDF herunterladen (Seite 11)

fig.10

fig.9

fig.8

Gas supply connection

• Check that the appliance is set for the type of gas available

and then connect it to the mains gas piping or the gas

cylinder in compliance with current regulations and

standards.

• This appliance is designed and set to work with the gas

indicated on the label situated on the actual hob. If the gas

supply is other than the type for which the appliance has

been set, proceed with replacing the corresponding nozzles

(provided), following instructions given in the paragraph

“Adaptation to different types of gas”.

• For trouble-free operation, suitable use of energy and longer

life of the appliance, make sure that the supply pressure

complies with the values indicated in the table 1 "burners

and nozzles specifications, otherwise install a special

pressure regulator on the supply pipe in compliance with

current standards and regulations.

• Connect in such a way that the appliance is subjected to

no strain whatsoever.

Either a rigid metal pipe with fittings in compliance with the

standards in force must be used for connecting to the nipple

union (threaded ½"G male fitting) situated at the rear of the

appliance to the right (fig.8), or flexible steel pipe in

compliance with the standards in force, which must not

exceed 2000 mm in length.

Should it be necessary to turn the fitting, the gasket (supplied

with the appliance) must be replaced. Upon completion of

installation, check the gas circuit, the internal connections

and the taps for leaks using a soapy solution (never a flame).

Also check that the connecting pipe cannot come into contact

with moving parts which could damage or crush it.

Make sure that the natural gas pipe is adequate for a sufficient

supply to the appliance when all the burners are lit

Important: A pressure regulator, in compliance with the

standards in force, must be inserted when connecting to a

liquid gas supply (in a cylinder).

Adaptation to a different type of gas

If the hob is to be converted for use with a type of gas other

than that for which it was set in the factory (indicated on the

label to be found on the hob), the burner nozzles should be

replaced as follows:

• Remove the pan supports and the burners.

• Unscrew the nozzles “A” (fig.9) using a 7 mm socket wrench

and replace them with the ones which have a diameter

suitable for the type of gas to be used, according to the

table 1 "burners and nozzles specifications).

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

Adjusting the low flame

• Put the tap to the low flame position (the burner should be

lit);

• Remove the tap knob (fig.10) and turn the adjusting screw,

situated to the side of the tap stem, using a screwdriver

(loosening the screw increases the height of the flame,

tightening decreases it).

note: the adjusting screw must be fully screwed down for

liquid gas.

• Having obtained the low flame setting required and with

the burner lit, abruptly change the position of the knob

several times from minimum to maximum and vice versa

and check that the flame does not go out.

• Refit the tap knobs

If an electric fan is used for extracting the combustion

products, the ventilation aperture must be increased in relation

to its maximum performance. The electric fan should have a

sufficient capacity to guarantee an hourly exchange of air

equal to 3-5 times the volume of the kitchen. Prolonged,

intensive use of the appliance may require extra ventilation,

e.g. an open window or a more efficient ventilation system

by increasing the extraction power of the electric fan if

installed. Liquid petroleum gas descends towards the floor

as it is heavier than air. Apertures in the outside walls in

rooms containing LPG cylinders should therefore be at floor

level, in order to allow any gas from leaks to be expelled. Do

not store LPG cylinders (even when empty) in basements/

rooms below ground level; it is advisable to keep only the

cylinder in use in the room at any one time and connected

far from heat sources which could raise its temperature to

above 50°C.

THE APPLIANCE MUST BE EARTHED

The appliance is designed to work with alternating current at

the supply voltage and frequency indicated on the rating plate

(situated on the rear part of the appliance and on the last

page of the instruction booklet) or at the end of the instruction

booklet. Make sure that the local supply voltage corresponds

to the voltage indicated on the rating plate.

(only for mod.KP 59)

ATTENTION: This appliance has a maximum power

exeeding 3kW; it is therefore necessary for it to be

connected to a socket able to support a rated current

higher than 13A (the appliance rated current is 15A).

Connecting the supply cable to the mains electricity

supply A 13. A plug in compliance whit BS 1362 is not

suitable.

To connect directly to the mains supply, a double-pole switch

with a contact separation of at least 3 mm suitable for the

load and complying with current standards and regulations,

ELECTRICAL CONNECTION

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit KP59MS-CX-G Bedienungsanleitung Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küche Indesit KP59MS-CX-G