Indesit BC 99 T P XA AUS S Bedienungsanleitung PDF herunterladen (Seite 7)

AUS

Fitting the power supply cable

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram).

2. Install the power supply

cable by loosening the

cable clamp screw and the

three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see table).

The appliance must be directly connected to the mains using

an omnipolar switch with a minimum contact opening of 3

mm installed between the appliance and the mains. The

switch must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point (the back

panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply, make

sure that

• Theapplianceisearthedandtheplugiscompliantwith

the law.

• The socketcanwithstand the maximumpowerof the

appliance, which is indicated on the data plate.

• Thevoltageisintherangebetweenthevaluesindicated

on the data plate.

• Thesocketiscompatiblewiththeplugoftheappliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 41 cm

depth 41 cm

Volume* 74 l

Dimensions**

width 45.6 cm

height 41 cm

depth 41 cm

Volume** 77 l

Electrical

connections

voltage: 220 - 240 V~ 50 Hz

maximum power absorbed

3400 W (see data plate)

ENERGY LABEL

Directive 2002/40/EC on the

label of electric ovens.

Standard EN 50304

Declared energy consumption

for Forced convection

Class – heating mode:

Conventional oven.

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments – 2004/108/EEC

dated 15/12/04

(Electromagnetic

Compatibility) and subsequent

amendments - 93/68/EEC

dated 22/07/93 and

subsequent amendments.

2002/96/EEC and subsequent

amendments.

1275/2008 Stand-by/off mode

* Only for models with drawn rails.

** Only for models with wire rails.

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit BC 99 T P XA AUS S Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit BC 99 T P XA AUS S