Indesit FH G (BK)/HA Bedienungsanleitung PDF herunterladen (Seite 22)

There is an adjustable L-shaped pipe tting on the appliance

supply ramp and this is tted with a seal in order to prevent

leaks. The seal must always be replaced after rotating the pipe

tting (the seal is provided with the appliance). The gas supply

pipe tting is a threaded 1/2 gas cylindrical male attachment.

Connecting a exible jointless stainless steel pipe to

a threaded attachment

The gas supply pipe tting is a threaded 1/2 gas cylindrical male

attachment. These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once connection has

been carried out, make sure that the exible metal pipe does

not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current National

regulations.

Checking the tightness of the connection

! When installation has been completed, check the pipe

ttings for leaks using a soapy solution. Never use a ame.

Adapting to different types of gas

In order to adapt the oven to a type of gas other than the

type for which it was manufactured (indicated on the label),

follow these simple steps:

• Replacing the oven burner nozzle

1. Open the oven door fully.

2. Slide out the bottom of the

oven.

3. Unscrew the burner

fastening screws.

4. Remove screw “V” and

then the oven burner.

5. Unscrew the oven burner

nozzle using the special

socket spanner for the

nozzles, or better still a 7 mm

socket spanner, and replace

it with a nozzle suited to the

new type of gas (see Table 1).

6. Replace all the parts, following the steps described above

in the reverse order.

! Take particular care when handling the spark plug

wires and the thermocouple pipes.

• Primary air regulation for the oven burner

The burner was designed not to need any adjustments to

the primary air.

• Setting the oven burner to minimum

1. Turn the knob rst to the Max setting for about 10 minutes

and then to Min.

2. Remove the knob.

3. Remove the disk fastened to the control panel.

4. Adjust the screw located outside the thermostat cock pin

until the ame is small but steady (the ame can be seen

through the slots on the oven bottom).

5. Make sure the burner does

not switch off when you turn

the knob from Max to Min

quickly, or when you open

and close the oven door

quickly.

! If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

! Once this procedure is nished, replace the old rating

sticker with one indicating the new type of gas used. This

sticker is available from any of our Service Centres.

! If the gas pressure is different from the recommended

pressure, a suitable pressure regulator must be tted to the

inlet pipe in accordance with current National Regulations.

DATA PLATE

Dimensions

width 43.5 cm

height 31 cm

depth 43.5 cm

Volume

58 l

Electrical

connections

see data plate

Gas features

see data plate

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments - 2004/108/EEC

dated 15/12/04 (Electromagnetic

compatibility) and subsequent

amendments - 93/68/EEC dated

22/07/93 and subsequent

amendments. 2009/142/EEC

dated 30/11/09 (Gas) and

subsequent amendments.

2012/19/EC and subsequent

amendments.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FH G (BK)/HA Bedienungsanleitung Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Mikrowellen Indesit FH G (BK)/HA