Indesit FD 61.1 (WH)/HA S Bedienungsanleitung PDF herunterladen (Seite 19)

Fitting the power supply cable

1. Open the terminal board by

inserting a screwdriver into the side

tabs of the cover. Use the screwdriver

as a lever by pushing it down to open

the cover (see diagram).

2. Install the power supply cable by

loosening the cable clamp screw

and the three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals: the Blue

wire to the terminal marked (N), the

Brown wire to the terminal marked

(L) and the Yellow/Green wire to the

terminal marked (see diagram).

3. Secure the cable by fastening the

clamp screw.

4. Close the cover of the terminal

board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate (see table).

The appliance must be directly connected to the mains using an omnipolar

switch with a minimum contact opening of 3 mm installed between the

appliance and the mains. The switch must be suitable for the charge indicated

and must comply with current electrical regulations (the earthing wire must not

be interrupted by the switch). The supply cable must be positioned so that it

does not come into contact with temperatures higher than 50°C at any point

(the back panel of the oven, for example).

! The installer must ensure that the correct electrical connection has been

performed and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• The voltage is in the range between the values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures

not be observed.

Electrical

connections

voltage:

220-230V~ or 220-240V~

50/60Hz or 50Hz

(see data plate)

maximum power absorbed 2800W

ENERGY

LABEL

APPLIANCE SPECIFICATIONS

Dimensions*

width 43,5 cm

height 32,4 cm

depth 40,6 cm

Dimensions**

width 45,5 cm

height 32,4 cm

depth 40,6 cm

Volume*

58 lt.

Volume**

60 lt.

* Only for models with drawn rails.

** Only for models with wire rails.

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

Energy consumption for Natural

convection – heating mode:

Traditional mode

Declared energy consumption for

Forced convection Class –

heating mode: Baking

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments

- 2004/108/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 2012/19/EC and subsequent

amendments.

1275/2008 standby/off mode.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FD 61.1 (WH)/HA S Bedienungsanleitung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Mikrowellen Indesit FD 61.1 (WH)/HA S