6
GB
Brown - Live
If the colours of the wires in the mains lead do not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked “E” or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured
Red.
Connect Blue wire to terminal marked “N” or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a 13 amp fuse. A 15 amp plug must be protected
by a 15 amp fuse, either in the plug or adaptor or at
the distribution board. If you are in any doubt about the
electrical supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE “NEUTRAL” (“N”)
BROWN “LIVE” (“L”)
GREEN AND YELLOW “EARTH” (“E”)
Disposing of the appliance
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible to
the plug body and dispose of it as described above.
Adapting the cooker to
different types of gas
In order to adapt the cooker
to a different type of gas with
respect to the gas for which it
was produced (indicated on the
label attached to the lid), follow
these steps:
a) replace the hose holder mounted on the
appliance with that supplied in the bag of “cooker
accessories”.
b) Replacing the burner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket
spanner, and replace them with nozzles for the
new type of gas (see table 1 “Burner and nozzle
characteristics”).
• replace all the components by repeating the steps in
reverse order.
c) Minimum regulation of the hob burners:
• turn the tap to minimum;
• remove the knob and adjust the regulation screw,
which is positioned in or next to the tap pin, until the
flame is small but steady.
! in the case of liquid gas, the regulation screw must
be screwed in to the bottom.
• check that the flame does not
turn off when you turn the tap
quickly from high to low.
d) Regulating the
primary air of the burners:
The primary air of the burners
requires no regulation.
Adapting to different types of gas
In order to adapt the oven to
a different type of gas with
respect to the gas for which it
was manufactured (indicated
on the label), follow these
simple steps:
a) Replacing the oven burner
nozzle
• open the oven door fully
• pull out the sliding oven bottom
V
V
Z
• Pry the fixing tab “V” and remove the oven burner
• Unscrew the oven burner nozzle using the socket
spanner for the nozzles “Z”, or a 7 mm socket
spanner, and replace it with a nozzle suited to the
new type of gas (see Table 1).
Take particular care handling the spark plug wires
and the thermocouple pipes.
• Replace all the parts, following the steps described
above in the reverse order.
b) Minimum regulation of the gas oven burner with
thermostat:
• light the burner as described in the paragraph “the
oven knob” of the instruction booklet.
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
unscrew the two screws and take off the shield
protecting the burner (in main oven burner only).
(84 Seiten)
(44 Seiten)
(52 Seiten)
(32 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern