Indesit DIS-14 Bedienungsanleitung PDF herunterladen (Seite 14)

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• The socket is earthedandcomplies with current

regulations.

• Thesocket can withstand the maximum load of the

appliance, which is indicated on the data plate located

on the inside of the door

(see chapter entitled Description

of the appliance).

• Thepowersupplyvoltagefallswithinthevaluesindicated

on the data plate on the inside of the door.

• Thesocketiscompatiblewiththeplugoftheappliance.

If this is not the case, ask an authorised technician to

replace the plug

(see Assistance)

; do not use extension

cables or multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order

to protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add only then approximately 1 kg of salt

(see chapter entitled Rinse aid and refined salt)

. The water

may overflow: this is normal and is not a cause for concern.

Select the water hardness value

(see chapter entitled Rinse

aid and refined salt)

. - After the salt has been poured into

the machine, the LOW SALT indicator light

* switches off.

If the salt container is not filled, the water softener and

the heating element may be damaged as a result.

Technical data

Dimensions

width 44.5 cm

height 82 cm

depth 57 cm

Capacity 10 standard place-settings

Water supply pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply voltage See appliance data plate

Total absorbed power See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage

-2004/108/EC (Electromagnetic

Compatibility)

-2009/125/EC (Comm. Reg.

1016/2010) (Ecodesign)

-97/17/EC (Labelling)

-2012/19/ EC (Waste Electrical

and Electronic Equipment WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a nor-

mal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption

even further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

Standard conditions* User conditions**

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration (min/

cycle)

INTENSIVE

1,30 14 150 1,15 14 140

NORMAL

1,05 14 115 0,95 13 110

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit DIS-14 Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit DIS-14