Indesit TCD G51 XB (FR) Bedienungsanleitung PDF herunterladen (Seite 30)

The Controls

! Warning, after pressing the START/PAUSE button ,

the programme cannot be changed. To change a selected

programme, press the START/PAUSE button

the light

flashes Amber to indicate the programme is paused. Select

the new programme and any options required, the light will

then flash green. Press the START/PAUSE button

again

and the new programme will start.

• Option buttons

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected, by pressing a programme selection

button, before an option can be selected. Not all options

are available for all programmes. If an option is not

available and you press the button, the buzzer will

beep 3 times. If the option is available the indicator, on the

display unit next to the bottom buttons, lights to show that

the option has been selected.

Delay Timer (Time Delay)

The start of some programmes can be delayed for up to 24

hours. Ensure the water container is emptied before setting

a delayed start.

Pre Care

This option is only available if a delayed start has been

selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

Post Care

TWhen available and selected, the clothes are occasionally

tumbled after the end of the drying and cool tumble cycles,

to help prevent creases developing should you not be

available to remove the load immediately the programme is

complete.

Note: The Start/Pause light flashes Amber during this

phase.

Heat Level button, Display and Icons

Not all programmes allow you to change the heat level and

some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the display briefly shows

the selected heat level, along with a display of the selected

level icon:

HIGH HEAT

MEDIUM HEAT

LOW HEAT

Sound

Available on all programmes and allows the buzzer to give a

signal at the end of the drying cycle, to remind you that the

clothes are ready to be removed.

Mini Load

Available with programmes: Cotton High Heat 4kg and

Synthetic Medium Heat 1kg.

This option optimises Automatic programme for smaller

loads and improves the Time to End estimation.

• TIME DISPLAY

The display shows either the amount of time delay remaining or

an indication of the amount of time left for a drying programme

(see The Display). The display also shows if there is a problem

with your dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

• Empty Water Container

(Messages about emptying can be ignored if you have plumbed

your dryer into a drain as there is no need to empty the water

container). Messages are displayed to reminds you to empty

the water container (see The Display). If the water container fills

during a programme, the heater turns off and the dryer does a

period of Cool Tumble. After this it stops and a message tells

you to

EMPTY THE WATER CONTAINER

. You must empty the water

container and restart the dryer or the clothes will not dry. After

re-starting the dryer the message will take a few seconds to go

out. To avoid this always empty the water container each time

you use the dryer (see Maintenance).

• Door Opening

Opening the door during a programme will stop the dryer and

have the following effects:

Note: The START/PAUSE

light flashes Amber during the

Post Care phase of a programme

• The display shows

PAUSED

• During a delay phase the delay will continue to count down.

The START/PAUSE

button must be pressed to resume

the delay programme. The display will change to show current

status.

• The START/PAUSE

button must be pressed to resume

the programme. The display will change to show the

current status.

• During the Post Care phase, the programme ends. Pressing

the START/PAUSE

button will restart a new programme

from the beginning.

• Note

If you have a power cut, switch off the power or remove the

plug. When power is restored, press and hold the On/Off

button until the display briefly shows

POWER ON

and the dryer

reactivates. Then press the START/PAUSE

button and the

programme will resume.

Start and Programmes

1 2 ... 25 26 27 28 29 30 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit TCD G51 XB (FR) Bedienungsanleitung Seite 30

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wäschetrockner Indesit TCD G51 XB (FR)