Indesit SV70SP XA Bedienungsanleitung PDF herunterladen (Seite 7)

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate

with alternating current at the voltage and frequency indicated on the data

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by inserting

a screwdriver into the side tabs of the

cover. Use the screwdriver as a lever

by pushing it down to open the cover

(see diagram).

2. Install the power supply cable by

loosening the cable clamp screw

and the three wire contact screws

L-N- .

Connect the wires to the corresponding

terminals: the Blue wire to the terminal

marked (N), the Brown wire to the

terminal marked (L) and the Yellow/

Green wire to the terminal marked

(see diagram).

3. Secure the cable by fastening the

clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate (see table).

The appliance must be directly connected to the mains using an omnipolar

switch with a minimum contact opening of 3 mm installed between the

appliance and the mains. The switch must be suitable for the charge indicated

and must comply with current electrical regulations (the earthing wire must not

be interrupted by the switch). The supply cable must be positioned so that it

does not come into contact with temperatures higher than 50°C at any point

(the back panel of the oven, for example).

! The installer must ensure that the correct electrical connection has been

performed and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• The voltage is in the range between the values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures

not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 41 cm

depth 41 cm

Volume*

74 l

Dimensions**

width 45.6 cm

height 41 cm

depth 41 cm

Volume**

77 l

Electrical

connections

voltage: 220-240V~ 50Hz

maximum power absorbed 3400W

(see data plate)

* Only for models with drawn rails.

** Only for models with wire rails.

EU Directive no 65/2014

supplementing Directive 2010/30/EU.

EU Regulation no 66/2014

implementing Directive 2009/125/EC.

Standard EN 60350-1

Standard EN 50564

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EC of 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EU and subsequent

amendments.

1275/2008 Stand-by/off mode

Declared energy consumption

for Forced convection Class –

heating mode:

Conventional oven

ENERGY LABEL

and

ECODESIGN

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit SV70SP XA Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit SV70SP XA