Indesit KN3T65SA(X)/NL S Bedienungsanleitung PDF herunterladen (Seite 27)

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and does

not come into contact with moving parts.

Checking the connection for leaks

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner

(see  gure), and replace them with nozzles suited to

the new type of gas(see Burner and nozzle speci cations

table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners’

minimum setting:

1. Turn the tap to the minimum

position.

2. Remove the knob and adjust

the regulatory screw, which is

positioned inside or next to the

tap pin, until the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa several

times, checking that the flame is not extinguished.

! The hob burners do not require primary air

adjustment.

Adjusting the gas oven burner’s minimum setting:

1. Light the burner (see Start-up and Use).

2. Turn the knob to the minimum position (MIN)

after it has been in the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the

outside of the thermostat pin (see  gure) until the flame

is small but steady.

! If the appliance is connected to liquid gas, the

adjustment screw must be fastened as tightly as

possible.

5. Turn the knob from the MAX position to the MIN

position

quickly

or open

and shut

the oven

door,

making

sure that

the burner is not extinguished.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their housing.

The burner consists of two separate parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner. Replace the

nozzles with models that are configured for use with the new type of

gas (see Table 1). The two nozzles have the same hole diameter.

3. Replace all the components by completing the above operations in

reverse order.

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw, which is

positioned in or next to the tap pin, until the flame is small but

steady.

3. Having adjusted the flame to the required low setting, while the

burner is alight, quickly change the position of the knob from

minimum to maximum and vice versa several times, checking that

the flame does not go out.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit KN3T65SA(X)/NL S Bedienungsanleitung Seite 27

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit KN3T65SA(X)/NL S