Indesit FZ 891 P.1 IX AUS/G Bedienungsanleitung PDF herunterladen (Seite 3)

Electrical connection

! Ovens equipped with a three-pole power supply cable

are designed to operate with alternating current at the

voltage and frequency indicated on the data plate

located on the appliance (

see below

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the side

tabs of the cover. Use the

screwdriver as a lever by

pushing it down to open

the cover (

see diagram

2. Install the power

supply cable by

loosening the cable

clamp screw and the

three wire contact screws

L-N-

. Connect the

wires to the

corresponding terminals:

the Blue wire to the

terminal marked (N), the

Brown wire to the terminal

marked (L) and the

Yellow/Green wire to the

terminal marked

(

see

diagram

3. Secure the cable by

fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the electricity supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (

see table

The appliance must be directly connected to the mains

using an omnipolar switch with a minimum contact

opening of 3 mm installed between the appliance and the

mains. The switch must be suitable for the charge

indicated and must comply with current electrical

regulations (the earthing wire must not be interrupted by

the switch). The supply cable must be positioned so that

it does not come into contact with temperatures higher

than 50°C at any point.

! The installer must ensure that the correct electrical

connection has been made and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate (

see

below

• The voltage is in the range between the values

indicated on the data plate (

see below

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the plug,

ask an authorised technician to replace it. Do not use

extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (

see Assistance

The manufacturer declines any liability should theseThe manufacturer declines any liability should these

The manufacturer declines any liability should these

safety measures not be observed.safety measures not be observed.

safety measures not be observed.

TABLE OF CHARACTERISTICS

Dimensions

width 43.5 cm

height 32 cm

depth 40 cm

Volume 56 l

Electrical

connections

voltage: 220 - 240 V~ 50/60Hz

maximum power absorbed 2800 W

ENERGY

LABEL

Directive 2002/40/EC on the label of

electric ovens. Standard EN 50304

En er gy cons umpt i on fo r Na tural

convection – heating mode:

Traditional mode

Declared energy consumption for

Forced convection Class – heating

mode: Baking

This appliance conforms to the

following European Economic

Community directives: 2006/95/EEC

dated 12/12/06 (Low Voltage) and

subsequent amendments –

2004/108/EEC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments -

93/68/EEC dated 22/07/93 and

subsequent amendments.

2002/96/EC and subsequent

amendments.

1275/2008 Stand-by/off mode

1 2 3 4 5 6 7 8 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit FZ 891 P.1 IX AUS/G Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit FZ 891 P.1 IX AUS/G