Indesit C34S N17(W) RU/HA S Bedienungsanleitung PDF herunterladen (Seite 18)

Connecting a flexible jointless stainless steel

pipe to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance

is a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and

does not come into contact with moving parts.

Checking the connection for leaks

When the installation process is complete, check

the hose fittings for leaks using a soapy solution.

Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off

their seats.

2. Unscrew the nozzles using

a 7 mm socket spanner (

see

figure

), and replace them with

nozzles suited to the new type

of gas (

see Burner and nozzle

specifications table

3. Replace all the components

by following the above instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory

screw, which is positioned inside or next to the tap

pin, until the flame is small but steady.

! If the appliance is connected to a liquid gas

supply, the regulatory screw must be fastened as

tightly as possible.

3. While the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame is not

extinguished.

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used

with a different type of gas, replace the old rating

label with a new one that corresponds to the new

type of gas (these labels are available from

Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

to “regulators for channelled gas”.

! If one or more of these conditions is not fulfilled or

if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (

see below

TECHNICAL DATA

Oven dimensions

(HxWxD)

34x38x44 cm

Volume

63 l

Useful

measurements

relating to the

oven

compartment

width 42 cm

depth 44 cm

height 17 cm

Power supply

voltage and

frequency

see data plate

Burners

may be adapted for use with any

type of gas shown on the data

plate, which is located inside the

flap or, after the oven compartment

has been opened, on the left-hand

wall inside the oven.

ENERGY LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN

50304

Declared energy consumption for

Natural convection Class – heating

mode:

Static

EC Directives: 2006/95/EC dated

12/12/06 (Low Voltage) and

subsequent amendments -

2004/108/EC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments -

2009/142/EC dated 30/11/09 (Gas)

and subsequent amendments -

2002/96/EC.

1275/2008 Stand-by/ Off mode

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit C34S N17(W) RU/HA S Bedienungsanleitung Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit C34S N17(W) RU/HA S