Indesit 7OFH1037C IXRU/HA S Bedienungsanleitung PDF herunterladen (Seite 14)

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• All accessories - with the exception of the sliding racks

- can be washed like everyday crockery, and are even

dishwasher safe.

• We recommend that detergents are not sprayed directly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning purposes, the oven door may

be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

3. Grip the door on the two outer

sides and close it approximately

half way. Pull the door towards you,

lifting it out of its slot (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb and

replace it with a similar one:

halogen lamp voltage 230 V,

wattage 25 W, cap G 9.

3. Replace the glass cover

(see diagram).

! Do not touch the light bulb directly with your hands.

Glass cover

Lamp

Holder

compartment

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding

racks:

1. Remove the two frames,

lifting them away from the

spacers A (see gure).

2. Choose which shelf to use

with the sliding rack. Paying

attention to the direction in

which the sliding rack is to

be extracted, position joint B

and then joint C on the

frame.

3. Secure the two frames

with the guide rails using the

holes provided on the oven

walls (see diagram). The

holes for the left frame are

situated at the top, while the

holes for the right frame are

at the bottom.

4. Finally, t the frames on

the spacers A.

! Do not place the sliding racks in position 5.

Side and rear catalytic liners*

These are panels coated with a special enamel, which is

able to absorb the fat released by food as it cooks.

This enamel is quite strong, so that the various accessories

(racks, dripping pans, etc.) can slide along them without

damaging them. White marks may appear on the surfaces;

these are not a cause for concern.

Nevertheless, the following should be avoided:

- scraping the enamel with sharp objects (a knife, for

example);

- using detergents or abrasive materials.

Left

guide rail

Right guide

rail

Direction

of extraction

* Only available on certain models.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit 7OFH1037C IXRU/HA S Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit 7OFH1037C IXRU/HA S