Indesit IS5G1KMW/U Bedienungsanleitung PDF herunterladen (Seite 3)

Use pots and pans with bottoms the same

width as that of the burners or slightly larger (see

specific table). Make sure pots on the grates do

not protrude beyond the edge of the hob.

Improper use of the grids can result in damage

to the hob: do not position the grids upside down

or slide them across the hob.

Do not let the burner flame extend beyond the edge of the pan

Do not use : Cast iron griddles, ollar stones, terracotta pots and pans.

Heat diffusers such as metal mesh, or any other types. Two burners

simultaneously for one receptacle (e.g. Fish kettle).

Should particular local conditions of the delivered gas make the ignition

of burner difficult, it is advisable to repeat the operation with the knob

turned to small flame setting.

In case of installation of a hood above the cooktop, please refer to the

hood instructions for the correct distance.

The protective rubber feet on the grids represent a chocking hazard for

young children. After removing the grids, please ensure that all the feet

are correctly fitted.

GAS CONNECTION

WARNING : Prior to installation, ensure that the

local distribution conditions (type of gas and gas

pressure) and the configuration of the appliance

are compatible.

Check that the pressure of the gas supply is

consistent with the values indicated in Table 1

(“Burner and nozzle specifications”).

WARNING : The configuration conditions of

this appliance are stated on the label (or data

plate).

WARNING : This appliance is not connected

to a combustion products evacuation device. It

must be installed and connected in accordance

with current installation regulations. Particular

attention must be paid to the relevant

requirements regarding ventilation.

If the appliance is connected to liquid gas, the

regulation screw must be fastened as tightly as

possible.

IMPORTANT : When the gas cylinder or gas

container is installed, it must be properly settled

(vertical orientation).

WARNING : This operation must be perfomed

by a qualified technician

Use only a flexible or rigid metal hose for the

gas connection.

Connection with a rigid pipe (copper or steel):

Connection to the gas system must be carried

out in such a way as not to place any strain of

any kind on the appliance. There is an adjustable

L-shaped pipe fitting on the appliance supply

ramp and this is fitted with a seal in order to

prevent leaks. The seal must always be replaced

after rotating the pipe fitting (the seal is provided

with the appliance). The gas supply pipe fitting is

a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel

pipe to a threaded attachment: The gas supply

pipe fitting is a threaded 1/2 gas cylindrical male

attachment. These pipes must be installed so that

they are never longer than 2000 mm when fully

extended. Once the connection has been made,

make sure that the flexible metal pipe does not

touch any moving parts and is not compressed.

Only use pipes and seals that comply with current

national regulations.

IMPORTANT : If a staineless steel hose is used, it

must be installed so as not touch any moving parts

part of the furniture (e.g. drawer). It must pass

through an area where there are no obstructions

and where it is possible to inspect it across its

entire length.

Theapplianceshouldbe connectedtothemain

gas supply or to a gas cylinder in compliance with

the current national regulations. Before making

the connection, make sure that the appliance is

compatible with the gas supply you wish to use.

If it is not, follow the instructions indicated in the

paragraph "Adapting to different types of gas".

After connection to the gas supply, check for

leaks with soapy water. Light up the burners and

turn the knobs from max position 1* to minimum

position 2* to check flame stability.

Connection to the gas network or the gas

cylinder may be carryout using a flexible rubber

or steel hose, in accordance with current national

legislation.

ADAPTING TO DIFFERENT TYPES OF GAS

To adapt the appliance to a type of gas

other than the type for which it was manufactured

(indicatedontheratinglabel),followthededicated

steps provided after the intallation drawings.

INSTALLATION

The appliance must be handled and installed

by two or more persons - risk of injury. Use

protective gloves to unpack and install - risk of

cuts.

The electrical and gas connections must

comply with local regulations.

Installation, including water supply (if any),

electrical connections and repairs must be carried

out by a qualified technician. Do not repair or

replaceanypart of theapplianceunless specifically

statedin the usermanual. Keep childrenawayfrom

the installationsite. After unpackingtheappliance,

make sure that it has not been damaged during

transport. In the event of problems, contact the

dealer or your nearest Aftersales Service. Once

installed, packaging waste (plastic, styrofoam

parts etc.) must be stored out of reach of

children - risk of suffocation. The appliance must

be disconnected from the power supply before

any installation operation - risk of electric shock.

During installation, make sure the appliance does

not damage the power cable - risk of fire or electric

shock. Only activate the appliance when the

installation has been completed.

WARNING : Modification of the appliance and

its method of installation are essential in order to

1 2 3 4 5 6 7 8 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit IS5G1KMW/U Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Küchen- und Haushaltswarenzubehör Indesit IS5G1KMW/U