Indesit TI 6533 (NR) Bedienungsanleitung PDF herunterladen (Seite 10)

Electrical connections

Voltage,

Frequency

Fuses,

Sections

FR-AT-BE-DE-GP--

ES-IE-IL-IS-IT-LU-

RE-FI-GB-GR-PT--

SE-MA-NZ

230V-1+N~50 Hz

25 A*

2,5 mm²

FR-BE-NO

230V-2~50/60 Hz

25 A*

2,5 mm²

FR-BE-CH-DE-AT--

ES-IL-IT-NZ-PT-

MA- LU-SE-IS-NL

400V2-N~50 Hz

16 A*

1,5 mm²

FR-BE-NO

230V3~50 Hz

16 A*

1,5 mm²

230V2+2-N~50 Hz

16 A*

1,5 mm²

CY-AU-NZ-KW-MT

240V-1+N~50 Hz

25 A*

2,5 mm²

* Application of the simultaneity coefficient in accordance with

cei 60335-2-6 norm

Technical characteristics

This appliance conforms with the following

European Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic compatibility)

and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments;

- 2002/96/EC

he European Directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposed of in the normal

unsorted municipal waste stream. Old appliances must be

collected separately in order to optimise the recovery and recycling

of the materials they contain and reduce the impact on human

health and the environment. The crossed out “wheeled bin” symbol

on the product reminds you of your obligation, that when you

dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer for

information concerning the correct disposal of their old appliance.

Warning: If the hob is fitted above a built-in oven, the hob and

the oven must be connected to the mains separately for safety

reasons and to simplify operations when it is necessary to pull

the oven out for some reason.

Electrical connection

• The electrical safety of this appliance can only be guaran-

teed if the latter is correctly and efficiently earthed, in

compliance with regulations on electrical safety. Always

ensure that this vital safety measure has been taken. If

you have any doubts, call in a qualified technician to check

the electrical system thoroughly.

• The manufacturer denies all responsibility for damage

resulting from a system which has not been earthed cor-

rectly.

• Before powering the appliance, check whether the techni-

cal characteristics featured on the appliance data plate

correspond with those of the mains electrical system.

• Check that the current load of the mains supply and of the

power sockets is suitable for the maximum power of the

appliance, indicated on the appliance data plate. If in doubt,

contact a qualified professional.

Disconnect the appliance from the electricity supply be-

fore all operations.

Connect your hob to the electrical system by means of a

junction box: if the appliance is connected permanently to

the mains, an omnipolar circuit breaker, accessible if nec-

essary, with a minimum contact opening of 3 mm should be

installed.

Valid only for models with a power supply cable

Some models are supplied with a single-phase power supply

cable, and should consequently only be connected to the

single-phase mains. Observe the wire colours, as indicated

in the diagram attached.

Electrical connections Voltage, Frequency Fuses, Sections

FR-BE-AT-DE-GR-ES-IL-

IT-NZ-PT-GP-CH-MA-LU-

IE-FI-SE-IS-GB-NL-DK

230V - 1+N~ 50Hz

CY-MT-AU-NZ-KW

240V - 1+N~ 50Hz

25A *

2,5 mm²

FR-BE-NO

230V - 2 ~ 50Hz

BR=BRUN,BL=BLEU

BR=BRUIN, BL=BLAUW

BR=BRAUN, BL=BLAU

BR=BROWN, BL=BLUE

* Application of the simultaneity coefficient in accordance with

cei 60335-2-6 norm

Valid only for models without a power supply cable

Some models are not fitted with a power supply cable, as the

cable should be sized according to the type of electrical

connection in use (see connection table below). To connect

the cable, proceed as follows:

• Using a screwdriver, prise on the side tabs of the terminal

board cover;

• Pull open the cover of the terminal board.

To install the cable, proceed as follows:

• unscrew the wire clamp screw and the contact screws.

• to make the desired electrical connection (see table), use

the jumpers housed inside the box. Position the power

supply cable wires according to the indications in the table.

• once the connections have been made, tighten all the

terminal screws fully.

• Fasten the supply cable in place with the clamp and close

the cover of the terminal board.

L N

1 2 3 4 5

L1 L2

1 2 3 4 5

L1 L2 N

1 2 3 4 5

L1 L2 L3

1 2 3 4 5

N2N1

1 2 3 4

L N

1 2 3 4 5

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 37 38

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit TI 6533 (NR) Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Indesit TI 6533 (NR)