Indesit P 640 TC (IX) Bedienungsanleitung PDF herunterladen (Seite 6)

The hob must be at least 60 mm from the rear wall. If the

hob is to be installed near a corner, it must be at least 100

mm. from the side wall (fig.5). If the hob is installed on a

base unit with doors, hob operation is not influenced by the

opening and closing of these doors.

combustion of the gas and for ventilating the same room.

Air must be taken in naturally through permanent apertures

made in the outside walls of the room or through single or

branching collective ventilation ducts in compliance with the

standards in force. The air must be taken directly from the

outside, from an area far from sources of pollution.

The ventilation aperture must have the following

characteristics (fig.3A):

· total free cross section of passage of at least 6 cm² for

every kW of rated heating capacity of the appliance, with

a minimum of 100 cm² (the heating capacity is indicated

on the rating plate);

· it must be made in such a way that the aperture, both on

the inside and outside of the wall, cannot be obstructed;

· it must be protected, e.g. with grills, wire mesh, etc. in such

a way that the above-mentioned free section is not reduced;

· it must be situated as near to floor level as possible.

Detail A Adjacent Room to be

room ventilated

Examples of ventilation holes Enlarging the ventilation slot

for comburant air between window and floor

Fig. 3A Fig. 3B

The air inflow may also be obtained from an adjoining room,

provided the latter is not a bedroom or a room where there

is a risk of fire, such as garages, mews, fuel stores, etc. and

is ventilated in compliance with the standards in force.

Air from the adjoining room to the one to be ventilated may

be made to freely pass through permanent apertures with a

cross section at least equal to that indicated above. These

apertures may also be obtained by increasing the gap

between the door and the floor (fig.3B). If an electric fan is

used for extracting the combustion products, the ventilation

aperture must be increased in relation to its maximum

performance. The electric fan should have a sufficient

capacity to guarantee an hourly exchange of air equal to 3-

5 times the volume of the kitchen. Prolonged, intensive use

of the appliance may require extra ventilation, e.g. an open

window or a more efficient ventilation system by increasing

the extraction power of the electric fan if installed. Liquid

petroleum gas descends towards the floor as it is heavier

than air. Apertures in the outside walls in rooms containing

LPG cylinders should therefore be at floor level, in order to

allow any gas from leaks to be expelled. Do not store LPG

cylinders (even when empty) in basements/rooms below

ground level; it is advisable to keep only the cylinder in use

in the room at any one time and connected far from heat

sources which could raise its temperature to above 50 °C.

Fitting into modular kitchen units

For correct operation of the hob built into a kitchen unit or

other compartment, the latter must be suitable.

The installation diagram plus dimensions of the housing hole

is given in fig. 4.

fig.5

fig.4

Instructions for the installer

Installation above an oven

Suitable precautions must be taken to ensure that the

installation is in compliance with current accident-prevention

regulations regarding electrical and gas connections.

Both the electricity supply cable and the gas pipe must not

touch hot parts of the oven housing, in order to avoid

overheating. When installing above a built-under oven without

forced cooling ventilation, suitable air vents should be

provided for as shown in fig.6 (inlet at least 200 cm² from the

bottom, outlet at least 120 cm² from the top part) to allow

adequate ventilation inside the housing unit.

Also a wooden panel "A" should be installed beneath the

hob as insulation, positioning it at a minimum distance of 15

mm from the hob housing (fig.6).

Fixing to the housing unit

Proceed with fixing to the housing unit as follows (fig.7):

· mount the hooks "B", partly tightening the provided screws

"A" into the relative holes;

· position the provided sealing gasket "X" 5÷6 mm from the

edge of the installation hole, matching up the two ends of

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit P 640 TC (IX) Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Indesit P 640 TC (IX)