Indesit K3G11(W)/AUS Bedienungsanleitung PDF herunterladen (Seite 4)

AUS

* Only available in certain models.

Gas connection

This appliance is suitable for use with either a

flexible connection or rigid copper connection.

Check The Gas Type

WARNING: Before installation, check that the gas

type (natural gas or

LPG/Propane) of the

cooker is suitable for

the gas type available

to the installation. It is

extremely dangerous to

use the wrong gas type

with any appliance, as

fire or serious injury can

result.

This cooker is supplied

from the factory already set for Natural Gas. To

convert the cooker to LPG (or back to Natural Gas

from LPG), follow the directions later in this section.

Fit regulator supplied for Natural Gas (if applicable)

at rear of appliance, and as close as practicable to

the appliance.

It is recommended that an isolating valve and union

be fitted, to enable simple disconnection for

servicing. These are to be in an accessible location.

! Make sure the supply pressure conforms with the

values shown in the table entitled “Caracteristics of

the burners and nozzles”.

When the cooker is installed between cabinets

(recessed), the gas connection must be effected by

an approved flexible hose with bayonet fitting (BS

669 Current Edition). The gas inlet for the cookers is

a threaded G 1/2 gas female fitting.

700 mm

HOT PARTS

Connecting the gas supply

If a flexible hose is used, it should be as short as

possible with a maximum length of 1.5 metres;

• The flexible connection must be approved to

class B or D of AS/NZS1869 as a minimum.

• it should not be bent, kinked or compressed;

• it should not be in contact with the rear wall of the

appliance or in any case with parts which may

reach a temperature of 50°C;

• it should not come into contact with pointed parts

or sharp corners;

• it should not be subject to any pulling or twisting

forces;

• it should be easy to inspect along its entire length

in order to be able to check its condition.

• The supply connection point must be accessible

with the appliance installed.

• The inner diameters of the pipe are as follows:

8 mm for LPG; 13 mm for Natural Gas.

Upon completion of installation, check the gas

circuit, the internal connections and the taps for

leaks using a soapy solution (never a flame). Also

check that the connecting pipe cannot come into

contact with moving parts which could damage or

crush it. Make sure that the natural gas pipe is

adequate for a sufficient supply to the appliance

when all the burners are lit

! Some models can have their gas connection

inverted. It is important to make sure the safety

chain is always situated on the side which

corresponds to the hose holder (Fig. B).

Duplicate Data Plate

Where the data plate is obscured by cabinetry when

the cooker is in the installed position, place a

duplicate data plate on a surface of the cabinetry

adjacent to the cooker.

Electrial Connection

Power supply voltage and frequency: 230-240V a.c.

50/60 Hz.

! The supply cable must be positioned so that it

never reaches at any point a temperature 50°C

higher than the room temperature. The cable must

be routed away from the rear vents. Should you

require it, you may use a longer cable, however, you

must ensure that the cable supplied with the

appliance is replaced by one of the same

specifications in accordance with current standards

and legislation.

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Fig. A Fig. B

1 2 3 4 5 6 7 8 9 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit K3G11(W)/AUS Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Indesit K3G11(W)/AUS