Indesit LVTI 12-56 Bedienungsanleitung PDF herunterladen (Seite 13)

148

12083

121168

100

Installation

 Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given

away or moved, please ensure the manual is kept

with the machine, so that the new owner may

benefit from the advice contained within it.

 Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

 If the appliance must be moved at any time,

keep it in an upright position; if absolutely

necessary, it may be tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and

check that it has not been damaged during

transportation.

If it has been damaged, contact the retailer and

do not proceed any further with the installation

process.

2. Check the dishwasher by placing it so that its

sides or back panel are in contact with the

adjacent cabinets or even with the wall. This

appliance can also be recessed under a single

worktop* (

see the Assembly instruction sheet

3. Position the dishwasher on a level and sturdy

floor. If the floor is uneven, the front feet of the

appliance may be adjusted until it reaches a

horizontal position (the angle of inclination must not

exceed 2 degrees). If the appliance is levelled

correctly, it will be more stable and much less

likely to move or cause vibrations and noise while it

is operating.

4. Adjust the height of the rear feet from the front

of the appliance*: use a screwdriver to tighten or

loosen the screws on the lower part of the

dishwasher.

Connecting the water and electricity

supplies

 Connection to the water and electricity supplies

should only be performed by a qualified

technician.

 The dishwasher should not stand on top of the

water hoses or the electricity supply cable.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned

towards the right or the left in order to achieve the

best possible installation (

see figure

Connecting the water inlet hose

• To a suitable cold water connection point:

before attaching the hose, run the water until it

is perfectly clear so that any impurities that

may be present in the water do not clog the

appliance; after performing this operation,

screw the inlet hose tightly onto a tap with a ¾

gas threaded connection.

• To a suitable hot water connection point: your

dishwasher may be provided with hot water

from the mains supply (if you have a central

heating system with radiators) provided that it

does not exceed a temperature of 60°C.

Screw the hose to the tap as described for

connection to a cold water supply.

 If the inlet hose is not long enough, contact a

specialist store or an authorised technician (

see

Assistance

 The water pressure must be within the values

indicated in the Technical data table (

see below

 The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks

the water supply in the event of anomalies or

leaks from inside the appliance.

- is provided with a

Water Stop

* safety device, in

other words it has a water inlet hose that consists

of a transparent hose on the outside and a red

hose on the inside: both the hoses can withstand

extremely high pressure. If the internal hose

breaks, the external hose becomes a bright red

colour and carries the water instead, thus avoiding

any leakage.

 It is very important to check the external hose

regularly: if it is a bright red colour, it must be

replaced by an authorised technician as soon as

possible (

see Assistance

* Only available in selected models.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit LVTI 12-56 Bedienungsanleitung Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit LVTI 12-56