Indesit IDL 42 DE.C Bedienungsanleitung PDF herunterladen (Seite 22)

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned to

the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher, making

it level. In any case, the appliance should not be inclined

more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

This dishwasher model can be built under a single worktop

(please read the relevant instruction sheet).

Cold water connection.

Connect the cold water supply hose to a 3/4 gas threaded

connection, taking care to screw it tightly onto the tap. If the

water hoses are new or have been out of use for an extended

period of time, let the water run to make sure it is clear and

free of impurities before making the connection. If this

precaution is not taken, the water inlet could get blocked,

causing damage to your dishwasher.

- It is strongly recommended to use a new hose to connect

the dishwasher to the water supply line, and the old hose-

set should not be reused. Asking to specilized shop or an

authorized service technician (see Service).

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of 60°

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Anti-flooding protection

Your dishwasher is provided with a special system which

blocks the water supply in the event of leaks inside the

appliance. It is further equipped with a water inlet hose that

can withstand extremely high pressures and that turns bright

red in the event of breakage. Safety in the event of flooding

is ensured by the second clear hose that contains the former

and thus highlights the latter when it has turned bright red. It

is vital that you check it on a regular basis: if you see it has

turned bright red, then you know you have to replace it as

soon as possible. Call for an authorised technical engineer to

come and replace it.

Drain Hose Connection

Fit the drain pipe into a drain

line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. Use the special

plastic elbow provided (see fi-

gure) to position it in the best

possible way. The part of the

pipe marked with the letter A

should be between 40 and 100

cm above the ground.

The pipe should not be immersed in water.

Attention: The special plastic hose support must be

solidly fastened to the wall to prevent the drain hose from

moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for

the current in the home correspond to those on the rating

plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Caution:

- Once the appliance has been installed, the electrical plug

and socket should remain accessible.

- If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in

order to prevent all potential hazards. (See Assistance)

- The cable should not be bent or compressed.

- The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.

1 2 ... 17 18 19 20 21 22 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit IDL 42 DE.C Bedienungsanleitung Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit IDL 42 DE.C