Indesit IDL 750 AG.2 Bedienungsanleitung PDF herunterladen (Seite 2)

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

If the appliance must be moved at any time, keep it

in an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop (

see the Assembly instruction

sheet

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position (the angle of

inclination must not exceed 2 degrees). If the appliance is

levelled correctly, it will be more stable and much less

likely to move or cause vibrations and noise while it is

operating.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water supply

network using new piping.

- Do not use old piping.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned towards the

right or the left in order to achieve the best possible

installation (

see figure

Connecting the water inlet hose

• To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

a ¾ gas threaded connection.

• To a suitable hot water connection point: your

dishwasher may be provided with hot water from the

mains supply (if you have a central heating system

with radiators) provided that it does not exceed a

temperature of 60°C.

Screw the hose to the tap as described for

connection to a cold water supply.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (

see

Assistance

The water pressure must be within the values

indicated in the Technical data table (

see below

The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

- is provided with a

Water Stop

* safety device, in other

words it has a water inlet hose that consists of a

transparent hose on the outside and a red hose on the

inside: both the hoses can withstand extremely high

pressure. If the internal hose breaks, the external hose

becomes a bright red colour and carries the water

instead, thus avoiding any leakage.

 It is very important to check the external hose

regularly: if it is a bright red colour, it must be replaced

by an authorised technician as soon as possible (

see

Assistance

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

* Only available in selected models.

148

12083

121168

100

Installation

1 2 3 4 5 6 7 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit IDL 750 AG.2 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Indesit IDL 750 AG.2