Indesit OK 1037EL D.20 X/HA Bedienungsanleitung PDF herunterladen (Seite 23)

Electrical connection

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2. Install the power

supply cable: by

loosening the cable

clamp screw and the

three wire contact

screws L-N-

Connect the wires to

the corresponding

terminals: the Blue wire

to the terminal marked

(N), the Brown wire to

the terminal marked (L)

and the Yellow/Green

wire to the terminal

marked

(see

diagram).

3. Fix the cable in place by fastening the clamp

screw.

4. Close the terminal board cover.

Connecting the power supply cable to the

electricity mains

Install a standardised plug corresponding to the

load indicated on the data plate (see opposite).

The appliance must be directly connected to the

mains using an omnipolar switch with a minimum

contact opening of 3 mm installed between the

appliance and the mains. The switch must be

suitable for the charge indicated and must comply

with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply

cable must be positioned so that it does not come

into contact with temperatures higher than 50°C at

any point (the back panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully

compliant with safety regulations.

Before connecting the appliance to the power

supply, make sure that:

•The appliance is earthed and the plug is compliant

with the law.

• the socket can withstand the maximum power of

the appliance, which is indicated on the data

plate (see below);

• the voltage is in the range between the values

indicated on the data plate (see below);

• the socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be

easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

! The manufacturer declines any liability should

these safety measures not be observed.

APPLIANCE SPECIFICATIONS

width 43.5 cm

height 41 cm

depth 41 cm

Volume*

Dimension*

74 l

Electrical

connections

voltage: 220 - 240 V~ 50/60 Hz

maximum power absorbed

3400 W (see data plate)

ENERGY

LABEL

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

Declared energy consumption for

Forced convection Class –

heating mode: ECO

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC dated 12/12/06 (Low

Voltage) and subsequent amendments

– 2004/108/EEC dated 15/12/04 and

subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments

- 2002/96/EC and subsequent

amendments.

1275/2008 Standby/off mode

width 45.6 cm

height 41 cm

depth 41 cm

Volume**

Dimension**

77 l

* Only for models with drawn rails.

** Only for models with wire rails.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit OK 1037EL D.20 X/HA Bedienungsanleitung Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Öfen Indesit OK 1037EL D.20 X/HA