Indesit LAL85 FF1I W WTD Betriebsanweisung Seite 5

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 9
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 4
GB
5
Installation
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to operate
correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Place the device far from heat sources (direct sun light, electric
kitchen etc.)
50
mm
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical socket
ensure the following:
The appliance is earthed and the plug is compliant with the law.
The socket can withstand the maximum power of the appliance,
The voltage must be in the range between the values indicated
on the data plate located on the bottom left side (e.g. 220-
240V).
The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
! Electronic versions are provided with a motor protection switch
that powers on the compressor only almost 8 minutes after the
starting. The compressor also starts each time the power supply
is cut off whether voluntarily or involuntarily (blackout).
1. Connect the plug and check that the FRIDGE TEMPERATURE
indicator turns on. If the indicator stays off, please press the
ON/OFF button.
2. Set the FRIDGE TEMPERATURE on an average value. After a
few hours it will be possible to insert food in the fridge.
AIR*
It is recommended to enable the AIR pushing on the apposite
button to improve the functioning of the product with high
environment temperature, if there are water drops on the glass
shelves or in high humidity conditions.
Do not block the air inlet with food.
Using the refrigerator to its full potential
Place only cold or lukewarm foods in the compartment, never
hot foods (See MULTI USE DRAWER where present)
Remember that cooked foods do not last longer than raw foods.
Do not store liquids in open containers: they will increase the
level of humidity in the refrigerator and cause condensation to
form.
SHELVES: with or without grill.
They are removable and adjustable in height and depth thanks to
the special guides (see the picture), allowing easy storage of large
containers and food. Height can be adjusted without complete
removal of the shelf.
1
2
TEMPERATURE Indicator light*: to identify the coldest area in
the refrigerator.
1. Check that OK appears clearly on the indicator light (see
diagram).
* Varies by number and/or position, available only on certain
models.
Seitenansicht 4
1 2 3 4 5 6 7 8 9

Kommentare zu diesen Handbüchern

Keine Kommentare