Indesit K6G21(W)/R Bedienungsanleitung PDF herunterladen (Seite 15)

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

HOOD

900

Min. mm.

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

420

Min. mm.

Fig. C Fig. D

e) The wall in contact with the back of the cooker must be of

flameproof material.

Connecting the gas

The appliance should be connected to the mains or to a gas

cylinder in compliance with current directives. Before making the

connection, check that the cooker is regulated for the gas supply

you are using. If not, follow the instructions indicated in the

paragraph “Adapting to different types of gas”. On some models

the gas supply can be connected on the left or on the right, as

necessary; to change the connection, reverse the position of the

hose holder with that of the cap and replace replace the gasket

(supplied with the appliance). When using liquid gas from a cylinder,

install a pressure regulator which complies with current directive.

Important: check that the supply pressure complies with the

values indicated in table 1 “Characteristics of the burners and

nozzles” since this will ensure safe operation, correct consumption

and ensure a longer life to your appliance.

Connection with hose

Make the connection using a gas hose complying with the the

characteristics provided in current directive. The internal diameter

of the pipe used is as follows:

- 8mm for liquid gas;

- 13mm for methane gas.

When installing the hose, remember to take the following

precautions:

• No part of the hose should touch parts whose temperature

exceeds 50°C;

• The length of the hose should be less than 1500 mm;

• The hose should not be subject to twisting or pulling, and

should not have bends or kinks.

• The hose should not touch objects with sharp edges, any

moving parts, and it should not be crushed;

• The full length of the hose should be easy to inspect in order

to check its condition;

Check that the hose fits firmly into place at the two ends and fix

it with clamps complying to current directive.If any of the above

recommendations can not be adopted, flexible metal pipes should

be used.

Should the cooker be installed according to the conditions of

Class 2, subdivision 1, only a flexible metal pipe which is in

compliance with current safety standards should be used to make

the connection to the gas mains.

Connecting a flexible jointless stainless steel pipe to a

threaded attachment

Remove the hose holder fitted on the appliance. The gas supply

pipe fitting is a threaded 1/2 gas cylindrical male attachment.

Only pipes and gaskets complying with current directives. The

full length of the pipe must not exceed 2000 mm.

Tight control

Important: when installation has been completed, check the

pipe fitting for leaks with a soapy solution. Never use a flame.

Once the connection has been made, ensure that the flexible

metal tube does not touch any moving parts and is not crushed.

Connecting the supply cable to the mains

Install a normalised plug corresponding to the load indicated on

the data plate. When connecting the cable directly to the mains,

install an omnipolar circuit-breaker with a minimum contact

opening of 3 mm between the appliance and the mains. The

omnipolar circuit breaker should be sized according to the load

and should comply with current regulations (the earth wire should

not be interrupted by the circuit breaker).

The supply cable should be positioned so that it does not reach

a temperature of more than 50°C with respect to the room tem-

perature, along its length. Before making the connection, check

that:

• the limiter valve and the home system can support the

appliance load (see data plate);

• the mains is properly earthed in compliance with current

directives and regulations;

• there is easy access to the socket and omnipolar circuit

breaker, once the hob has been installed.

N.B: never use reducers, adaptors or shunts since they can

cause heating or burning.

Adapting the cooker to different types of gas

In order to adapt the cooker to a different type of gas with respect

to the gas for which it was produced (indicated on the label

attached to the lid), follow these steps:

a) replace the hose holder mounted on the appliance with that

supplied in the bag of “cooker accessories”.

Important: the hose holder for liquid gas is marked 8, the hose

holder for methane gas is marked 13. Always fit the sealing

gasket.

b) Replacing the burner nozzles on the hob:

• remove the grids and slide the burners from their housings;

• unscrew the nozzles using a 7 mm socket spanner, and

replace them with nozzles for the new type of gas (see table

1 “Burner and nozzle characteristics”).

• replace all the components by repeating the steps in reverse

order.

c) Minimum regulation of the hob burners:

•

turn the tap to minimum;

• remove the knob and adjust the regulation screw, which is

positioned in or next to the tap pin, until the flame is small but

steady.

N.B.: in the case of liquid gas, the regulation screw must be

screwed in to the bottom.

• check that the flame does not turn off when you turn the tap

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 69 70

Kommentare zu diesen Handbüchern

Keine Kommentare

Indesit K6G21(W)/R Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Barbrque & Grills Indesit K6G21(W)/R